Kem Cho, my friends! I am **Dilipbhai**, proprietor of **Shivam Water Solution** located at Vajepar Main Road, Morbi. For over 10 years, I have been personally installing, repairing, servicing, and custom-building domestic RO purifiers and commercial RO plants across Morbi, Rajkot, Wankaner, and surrounding ceramic hub regions.

One of the most frequent complaints homeowners and office managers bring to my shop is: *"Dilipbhai, my RO water purifier used to fill a container in 30 seconds, but now it only drips slowly! What is wrong with it?"*

If you are dealing with a trickle instead of a steady flow of pure drinking water, don't worry. Today, I am going to break down the top reasons why your domestic RO purifier loses water pressure and how we fix it here in Morbi and Rajkot.

---

## Why Does RO Water Flow Become Slow in Morbi & Rajkot?

Our groundwater in the Saurashtra region—especially around Morbi's industrial zones (like Trajpar, Mahendranagar, Sanala Road) and Rajkot's outskirts (Metoda, Kalawad Road)—is notorious for **extremely high TDS (Total Dissolved Solids)**, ranging anywhere from 800 PPM to over 2500 PPM. In addition, dust particles from nearby construction and ceramic factories frequently clog outer pre-filters.

When high-mineral hard water passes through fine RO filters, scale buildup happens quickly. Here are the 5 main causes of slow water flow in local purifiers:

### 1. Clogged Pre-Filter Spun Candle (Most Common!)
The outer pre-filter housing traps coarse dirt, sand, rust, and silt. In Morbi, due to heavy particulate matter in tap water, a standard PP spun filter can turn completely dark brown or black within 2 to 3 months. When this candle gets choked, water cannot reach the inner filters at full pressure.

### 2. Scaled or Clogged RO Membrane
The heart of your water purifier is the semi-permeable RO membrane (usually rated 75 GPD or 80 GPD). When exposed to hard borewell water over 6 to 12 months without proper antiscalant or timely pre-filter changes, microscopic pores in the membrane become blocked by calcium and magnesium salts. Water simply cannot pass through efficiently.

### 3. Weak or Failing RO Booster Pump
A domestic reverse osmosis system requires an input pressure of **60 to 80 PSI** at the membrane level to push pure water through. Over time, the pump head, diaphragm, or motor brushes wear out, reducing pressure even if the motor sounds like it is running fine.

### 4. Air Pressure Loss in Storage Tank
If you use a hydro-pneumatic storage tank model, the tank relies on an internal rubber bladder and compressed air (about 6 to 8 PSI when empty) to push water up through your faucet. If the tank loses air pressure or the bladder breaks, water stays trapped inside, leading to a weak trickle.

### 5. Choked In-line Carbon or Sediment Filters
Before reaching the membrane, water passes through activated carbon and sediment cartridges. Fine carbon dust or accumulated mineral sludge can restrict water velocity significantly.

---

## Dilipbhai’s Step-by-Step DIY Troubleshooting Guide

Before calling for a service technician, here are a few simple checks you can safely perform at home:

1. **Check the Outer Pre-Filter Bowl:** Turn off the main inlet valve, use the housing wrench to open the outer filter, and inspect the white spun candle. If it looks caked in mud, replace it immediately. (Tip: Keep a spare candle at home; they are inexpensive and easy to swap).
2. **Verify Feed Water Supply Valve:** Ensure the diverter valve connected to your kitchen tap is fully open and not partially restricted by limescale.
3. **Inspect the Waste Water Flow:** Switch on the RO unit and observe the reject (waste) pipe. If waste water is rushing out rapidly but no pure water drops into the tank, your RO membrane is likely scaled up or choked.

---

## Preventive Maintenance Tips for Long-Lasting RO Performance

To avoid sudden breakdowns and maintain healthy alkaline drinking water, follow this simple maintenance schedule tailored for Morbi and Rajkot conditions:

* **Change Pre-Filter Candle:** Every **2 to 3 months**.
* **Replace Sediment & Activated Carbon Filters:** Every **6 to 8 months**.
* **RO Membrane Replacement:** Every **12 to 18 months** (depending on raw water TDS levels).
* **Check Booster Pump Pressure & SMPS Adapter:** Annually during routine servicing.

---

## Need Honest, Expert RO Repair in Morbi or Rajkot?

If you have tried changing the pre-filter and your water flow is still slow, don't let a failing booster pump burn out your electrical adapter! Bring your purifier unit or give me a call. At **Shivam Water Solution**, we stock genuine high-pressure pumps, high-TDS membranes (Vontron, Dow Filmtec, CSM), food-grade fittings, and heavy-duty filter cartridges.

We provide doorstep service for residential RO systems, commercial office purifiers, and industrial water plants throughout Morbi, Rajkot, and neighboring regions.

### Contact Details:
* **Proprietor:** Dilipbhai
* **Shop Name:** Shivam Water Solution
* **Address:** Vajepar Main Road, Morbi - 363641, Gujarat
* **Phone / WhatsApp:** [+91 91730 96727](tel:+919173096727)
* **Services:** New Sales, Custom RO Fabrication, Filter Replacement, TDS Adjustment, Booster Pump Repair & AMC Services.

*Call Dilipbhai today for quick, affordable, and expert water purifier service right at your doorstep!*